Description
"8 Zone 3G Alarm System with Z-Wave Gateway"
Flexible 8 Zone control panel, 3G Cellular communicator and Z-Wave Gateway. Great starter kit to combine the versatile Ness 8 zone control panel and Z-Wave control in one package.
Supplied with 3G Communicator onboard, Powerful NAVIGATOR Touchscreen keypad, plug pack, battery, housing, IP232 Module and Ness G1 Z-Wave Gateway.
Feature Include:
* Operation and programming by SMS messaging
* Remote operation and programming via the free NessXCEL app
* Alarm reporting back to base by CID and/or self monitoring by SMS
* Powerful SMS accessibility including: arm/ disarm, programming, check system status,read alarm memory, receive alarm messages and operate AUX outputs all by SMS / TXT
* Supports SMS reporting
* Fully customisable word library for SMS messaging
* All-new KPX and Navigator Keypads supporting cellular operation
Includes Ness Telstra SIM locked to the Control Panel.
Smart Device Apps
zComms: iOS Ness zComms - Android Ness zComms
K-6006
d8
|
Control Panel D8XCel |
|
| 3G MODULE | Dual-Band UMTS/HSPA+ 800(850)/2100MHz Quad-Band GSM/GPRS/EDGE 850/900/1800/1900MHz |
| SIM CARD TYPE | Standard SIM |
| BOX DIMENSIONS (W - H - D) | 235 x 300 x 90 mm |
| POWER SUPPLY | 20VDC (Supplied) or 17VAC 1.4 Amp |
| POWER SUPPLY | 13.8v DC @ 800mA |
| QUIESCENT CURRENT DRAW | 80mA with 1 keypad |
| OPERATING VOLTAGE | 17VAC / 15V DC |
| RECHARGEABLE BATTERY | 12 volt 7.0 Amp/hour Sealed lead Acid |
| BATTERY CHARGING CURRENT | 350mA maximum, current limited |
| DYNAMIC BATTERY TEST | Backup battery is tested under load, hourly and on arming |
| FUSES | 2 Amp auto resetting / Siren output & Reset output. 500mA auto resetting / 12 volt auxiliary outputs. 200 mA auto resetting / Strobe output |
| ZONE OUTPUTS | 8 zone inputs. 2 x 24hr tamper inputs |
| END OF LINE RESISTOR | Choice of 12 programmable values including N/C. Default 2200 Ohms (2.2k) |
| MAXIMUM KEYPADS | 3. |
| INTEGRATED RADIO OPTIONS | Multi-pin connector for the optional Ness Radio Interface. Supports up to 55 Radio keys . Up to 8 radio zones |
| SERIAL HEADER | Serial data port for direct connect programming using NessCommsTM software. Also 2 way serial data |
| INTEGRATED ACCESS CONTROL | Multi-pin connector the optional Weigand Interface. Supports up to 3 Ness proximity access card readers |
| SIREN OUTPUT | On board siren driver with timed output. Maximum 3 x 8 Ohm horn speakers |
| STROBE OUTPUT | 12v DC timed output. Maximum 2 x 1 Watt strobe lights |
| RESET OUTPUT | 12v DC timed output. Max. 3 x 12v piezo screamers |
| EQUIPMENT POWER OUTPUT | 13.8v DC output for powering detectors and other equipment. Maximum 500mA |
| AUX READER | Multi-pin connector provides outputs Aux1, Aux2, Aux3, Aux4, 12v DC |
Z-Wave Gateway
| Models : | Ness G1 Z-Wave Gateway |
| Power : | DC 5V, 1.5A |
| Processors : | RISC CPU |
| Network Interface : | Ethernet 10BaseT/100BaseTX, Auto-MDIX, RJ-45 |
| Z-Wave Module : | Sigma Design 500 series module Tx RF Power : -26 ~ 2 dBm. Range: 100 meters open site 921.42 MHz |
| Buttons : | One reset button, to factory default settings, One WPS button for automatic WiFi setup |
| Indicators : | One LED for Internet connection status indication One LED for Ethernet connection indication One LED for Z_wave signal indication |
| Speaker : | Built-in 0.5W speaker for device inclusion/exclusion status indication |
| Installation : | Plug & play by ID/password. |
|
Management and |
Management software Ness zComms for multi-gateway management, Firmware upgrades via FTP |
| Supported Protocols : | IPv4, HTTP, TCP, ICMP, UDP, SNTP, FTP, DHCP, ARP, DNS, PPPoE, etc. |
| Accessories Included : | Power adaptor, RJ45 Ethernet cable, quick installation guide, ID/Password card. |
| App : | App Ness zComms for Android and iPhone/iPad |
| Alarm and Event Management : | Push notification on iPhone/iPad and Android devices. |
| Dimensions (HxWxD) : | 96 x 96 x 21 mm |
| Weight : | 129 g, incl. gateway bracket, excl. power adaptor |
| Approvals : | EMC - CE, FCC Part 15 Subpart B Class B Wireless RF - CE, FCC Part 15 Subpart C Power supply: CE, FCC, UL, EN 60950 |
| Operating conditions : | 0-50 °C Humidity 20 – 80% RH (non-condensing) |
 |
 |
 |
|
|
| D8Xcel BROCHURE | INSTALLATION MANUAL |
D8XCEL USER MANUAL |
Z-Wave Gateway BROCHURE |
Z-Wave Gateway MANUAL |
1 x 106-311 D8XCel panel with onboard 3G Dialler, complete with Power Supply and 12V 7 A/H Back Up Battery
1 x 106-100 D8/D16 Touchscreen Keypad
1 x 101-244 IP232 Ethernet Module
1 x 101-800 G1 Z-Wave Gateway
Additional Information
| Part Number | K-1301 |
|---|
You have no items in your shopping cart.
You have no items to compare.
